Best SMD6 Instalační příručka Strana 2
- Strana / 16
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
MODELS SMD6 • SMD8
Page 2
OUTSIDE AIR INTAKE LOCATION
Proper design and location of the outside air intake location is critical in
ensuring that the Damper can safely and reliably provide an opening for
fresh air to enter the home. The following requirements for the location
of the outside air intake must be met:
• Outside air intake is located a minimum of 10’ from combustion
appliance vents, chimneys, plumbing stacks, and bathroom or
kitchen exhaust vents. If local codes have more stringent separation
requirements, they shall apply.
TYPICAL INSTALLATIONS
Installations will vary according to the location in the home where the unit is installed and which model Damper is used. Use the following
illustrations and notes as guidance for your own installation. Always comply with local code requirements and in any instance where a detail
shown below conflicts with local code, the local code provision shall apply.
Damper connected to return side of central duct system.
• Outsideair intakeis placedhighenough abovegrade to prevent
blockage from snow or other debris such as leaves, and at a
minimum of 1’ above grade.
• Make-upairdampershouldnotdrawairfromcrawlspaces,garages,
attics, adjacent dwelling units, or any enclosed part of the building.
The Damper should be installed to draw air directly from outdoors.
OUTSIDE AIR INTAKE OPENING PROTECTION
Because the Damper, together with the end cap and outside air
duct which are installed with it, will allow outdoor air into the indoor
environment, it is important to meet the following requirements:
• Model641FA(6”)and643FA(8”)freshairinletwallcapsinclude
protective bird screens to keep out animals and outside debris.
Clean screens often and do not remove.
• Ifaprotectivebirdscreenotherthanthescreenprovidedisused,it
must cover the entire opening of the outside air duct. This screen
mustalsohaveopeningsofatleast¼”butnolargerthan½ ”.
• Theoutdoorairintakeopeningshouldmeetlocalcodeprovisions
for the protection of openings in exterior walls, including steps to
prevent moisture intrusion around the opening.
Note that the screen over the outside air opening is not a filter. It is
intended to prevent the intake of leaves, animals, or debris into the
outside air duct. A downstream filter is necessary to remove pollen,
dust, and other airborne particles. Potential filter locations are shown
below in the Typical Installations section.
MINIMUM RETURN AIR TEMPERATURE REQUIREMENTS
HVAC equipment manufacturers may have minimum requirements for
the air temperature in the return air plenum. Introducing outdoor air to
the return side of the central duct system may impact this temperature.
The installer should adjust both the size of the outside air duct and the
location of its connection to the return side of the central duct system in
a manner so that minimum air temperature requirements are satisfied
under design conditions.
AIR HANDLER UNIT
COOLING APPARATUS
AIR DISTRIBUTION FAN
HEATING APPARATUS
THERMOSTAT
CENTRAL SYSTEM SUPPLY AIR
REGISTER BOX ADAPTED
WITH SLIDE-IN FILTER (optional)
AUTO. MAKE-UP AIR DAMPER
FIELD MEASUREMENT OF OUTSIDE
AIR DUCT PRESSURE. (See “Install The
Damper” section on page 3 for damper
balancing instructions.)
FRESH AIR INLET WALL CAP
WITH BIRD SCREEN
INSULATED OUTSIDE
AIR DUCT (slope toward wall cap)
EXTERIOR WALL
VENTILATION AIR INTAKE
(locate away from pollutant sources)
CENTRAL SYSTEM RETURN AIR
FURNACE FILTER
PLAN THE INSTALLATION
Planning the installation first requires selecting the most appropriate
installation approach. The chart below offers suggestions for the most
effective installation approach by considering a few important factors.
Further details on the two main types of installations are provided below.
Yes
• House has central duct work?
Yes
• Return-air side of duct work is
accessible -either the return-air trunk
or return-air plenum?
Damper connected to
return side of central
duct system
No
No
Damper ducted directly
to a ceiling, floor, or wall
register
- AUTOMATIC MAKE-UP AIR DAMPER 1
- WITH TRANSFORMER AND 1
- TYPICAL INSTALLATIONS 2
- PLAN THE INSTALLATION 2
- INSTALL THE DAMPER 3
- LINKLOGIC 3
- TECHNOLOGY 3
- MAINTENANCE 4
- DAMPER LINKLOGIC™ 4
- CONTROL LINK INSTRUCTIONS 4
- FREQUENTLY ASKED 5
- QUESTIONS (FAQS) 5
- CLAPET AUTOMATIQUE D’AIR DE 6
- ET RELAIS 6
- MODÈLES SMD6 • SMD8 7
- INSTRUCTIONS DE LIAISON 9
- DE COMMANDE DU CLAPET 9
- LINKLOGIC™ 9
- ENTRETIEN 9
- FOIRE AUX QUESTIONS (FAQ) 10
- MODELOS SMD6 • SMD8 11
- Página 11 11
- Página 12 12
- Página 13 13
- CONFIGURACIÓN 14
- Página 14 14
- BOTÓN DE 14
- Página 15 15
- 99044540C 16
Související produkty a manuály pro ne Best SMD6
ne Best L7030 Technický list
(1 stránky)
(1 stránky)
ne Best 419 Informační leták
(2 stránky)
(2 stránky)
ne Best 408 Technický list
(2 stránky)
(2 stránky)
ne Best P195P2M70SB Informační leták
(1 stránky)
(1 stránky)
ne Best EB6 Technický list
(2 stránky)
(2 stránky)
ne Best 639 Informační leták
(2 stránky)
(2 stránky)
ne Best AEWPD318SB Specifikace
(1 stránky)
(1 stránky)
ne Best ARP8 Instalační příručka
(1 stránky)
(1 stránky)
ne Best WP28M30SB Uživatelský manuál
(1 stránky)
(1 stránky)
ne Best AFCROUND2 Instalační příručka
(1 stránky)
(1 stránky)
ne Best L7030 Technický list
(1 stránky)
(1 stránky)
ne Best PKEX2245 Příručka s rozměry
(1 stránky)
(1 stránky)
ne Best WC638 Technický list
(2 stránky)
(2 stránky)
ne Best AEWPD3054SBE Technický list
(4 stránky)
(4 stránky)
ne Best ALP36 Instalační příručka
(2 stránky)
(2 stránky)
ne Best UP27M30SB Uživatelský manuál
(1 stránky)
(1 stránky)
ne Best ABWPD36SB Instalační příručka
(2 stránky)
(2 stránky)
ne Best AEWP302SB Instalační příručka
(1 stránky)
(1 stránky)
ne Best IP29M42SB Uživatelský manuál
(1 stránky)
(1 stránky)
ne Best SMD6 Technický list
(1 stránky)
(1 stránky)
Sony SRF-V1BT manuals
Owner’s manuals and user’s guides for Unknown Sony SRF-V1BT.
We providing 4 pdf manuals Sony SRF-V1BT for download free by document types: User Manual
Komentáře k této Příručce